What Ails Electronics Ecosystem In India? – An Example

- Advertisement -

I took some time off from writing as I was involved in a series of development of plastic & sheet metal enclosures for a whole lot of products with different vendors in India and China. I could appreciate the difference in the end.

By Srinivasa Moorthy S A

We were planning to develop a plastic enclosure for a consumer product with an LCD display. We got the design done by the vendor’s design team in China and up front, the vendor told me that unless I get the plastics made by him he will not do the tooling. Before this whole lot of people told me that you should do the tooling in China/Taiwan and get the plastic moulded here in India. Let me tell that is difficult at least in China now. Most Chinese vendors don’t show interest unless there is manufacturing tied to it. They call themselves as “Solution Houses” no more design in India makes in China. This is true especially for Tablets, Mobile Phones, test instruments etc.

- Advertisement -
Image for representational purpose only

So we decided will do the design and tooling in India. We got the basic industrial design(ID) in quick time. While the ID houses are good in aesthetics not so good in usable design. It took almost a month to get usability in place. We took the design to the tool designer and they had a whole lot of questions even before they could quote. My learnings are;

  • Be sure about the volume that you need if you are not the tooling cost can go haywire. If you are not sure to go in for a single cavity ( that is, you can get one mould per cycle) and redo the tooling later for volume
  • Beware rapid prototype it will not tell the issues in the design especially moulding related like shrink marks, milling lines etc.
  • Most tool designers do the tooling by experience and they don’t use tools like Mould Flow. So if your plastic is complex insist on the analysis.
  • The only experience helps to solve post tooling mould related problems and go to a tool room that has good people.
  • Get your plastics done by the same vendor who does the tooling “DON’T TRY TO SEPARATE”. Tool design and moulding machines are closely connected doing it two places can kill the whole project.
  • The plastic part is costed by weight so know the weight to get the pricing right.
  • The tool has a life so if your volumes are high told them upfront to use the right tool block material
  • Go for a toolroom which has EDM wire cut machines, Vertical Milling has limitations.

Now coming to the lessons, in China all the above issues will not crop up as they know how to do it. This is a big difference. Don’t lose heart the part which we made in India cost us Rs.67 while in China it was costing 4USD ex-factory (about Rs 290). Landed cost will be much higher.

So it is the patience and knowing exactly what you want will make life easy. Interestingly we had challenges for the above part when we wanted to design silicon sleeve. Despite working with the vendor we could never get one sleeve that is close to what we can get from China! and we have to abandon the project!

Now coming to the sheet metal – while companies claim they have CNC machines to do the job the final enclosure has never been good. While CNC helps in cutting the sheet metal parts, where most of the vendors fail is in bending, welding and finishing. No sheet metal vendor has an understanding of Thermal & EMC/EMI issues. To address EMC/EMI issues you need partially exposed surfaces in the enclosures and that call for a different painting or power coating process. None of the vendors know this and you have to tell them. In China, the vendor asks do you need FCC/CE certification? If you say yes, he designs the enclosures accordingly. If your product has to meet Global Standards please be very clear about the welding, revetting and surface finishing (painting and powder coating).

None of the designers also understand this. The trouble I am seeing is that mechanical engineers have no appreciation of electronics issues (I now realise the course I use to take on electronic packaging and how important is that!) so they just give you a drawing and not design!

When I was interacting with the Chinese vendor I never faced these issues as they could easily understand the aspects. When I checked with them they were telling me their On Job Training is what makes the difference.

If we want to create a robust ecosystem we need to spend more time in design rather than copying ( I get requests for “Designing a copy of a sample product” as it is!).

Srinivasa Moorthy S A is the Chief Executive Officer of the Andhra Pradesh Electronics & IT Agency. He has over 30 years of experience in the IT industry as Head, Leader & Technocrat in the Electronic Product Design & Engineering Services.
- Advertisement -

Related Artcles

1 COMMENT

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Buzz

1Q23: Indian PC Shipments Fall 35% YoY, Still Above Pre-Pandemic Levels

0
Tablet shipments in India fell below the million-unit mark for the first time in two years As per the latest report from Canalys for Q1...

Tata Group Subsidiary To Set Up EV Battery Plant in Gujarat

0
Sources said that the decision to set up the EV battery plant at Sanand was taken around a week ago at a Tata...

MeitY Transfers Li-ion Battery Recycling Tech To Recycling Industry

0
The secondary raw materials could be used for battery manufacturing or in other potential applications Under the 'Promote Circularity Campaign' of Mission LiFE, the Ministry...

Exclusive

1Q23: Indian PC Shipments Fall 35% YoY, Still Above Pre-Pandemic Levels

0
Tablet shipments in India fell below the million-unit mark for the first time in two years As per the latest report from Canalys for Q1...

US PC Shipments Hit; Declined 28% Y-o-Y in 1Q23

0
Strong iPad performance led tablets shipments to perform relatively better Canalys forecasts the US PC shipments in 2024 to be 13% higher than...

IoT Analytics Lowers Five-Year IoT Market Outlook

0
The amount of money invested in global IoT start-ups decreased significantly in the last 12 months. Several major companies that were selling IoT...

Important Sectors

Tata Group Subsidiary To Set Up EV Battery Plant in Gujarat

0
Sources said that the decision to set up the EV battery plant at Sanand was taken around a week ago at a Tata...

MeitY Transfers Li-ion Battery Recycling Tech To Recycling Industry

0
The secondary raw materials could be used for battery manufacturing or in other potential applications Under the 'Promote Circularity Campaign' of Mission LiFE, the Ministry...

Centre Considers Cutting Import Duty On Solar Panels

0
The renewable energy ministry held talks with the finance ministry to reduce import duty on solar panels by half As per the latest report from...

Modified Semicon India: Govt Invites Applications For Setting Up Semicon & Display Fabs

0
Under the Modified Programme, a financial incentive of 50% of the project cost will be provided for setting up of semiconductor/ display fabs in...

British Gas Unveils The New Hive EV Charger

0
British Gas only provides £100 in credit to Hive customers who move to the EV rate and £50 in Hive vouchers with every order...

Manufacturing

Tata Group Subsidiary To Set Up EV Battery Plant in Gujarat

0
Sources said that the decision to set up the EV battery plant at Sanand was taken around a week ago at a Tata...

Centre Considers Cutting Import Duty On Solar Panels

0
The renewable energy ministry held talks with the finance ministry to reduce import duty on solar panels by half As per the latest report from...

Modified Semicon India: Govt Invites Applications For Setting Up Semicon & Display Fabs

0
Under the Modified Programme, a financial incentive of 50% of the project cost will be provided for setting up of semiconductor/ display fabs in...

British Gas Unveils The New Hive EV Charger

0
British Gas only provides £100 in credit to Hive customers who move to the EV rate and £50 in Hive vouchers with every order...

MeitY Invites Applications For Incentives Under PLI 2.0 For IT Hardware

0
The ministry notified the scheme on May 29 and plans to open the window of applications from June 01, 2023 With the aim to push...